Spin a wheel and listen. If it's quiet and keeps spinning for a few seconds, your bearings are fine. If it grinds, catches, or dies almost instantly, it's time to clean them, and the whole thing takes about 20 minutes with stuff you've probably already got lying around. That's the short version of how to clean skateboard bearings.
Do They Actually Need Cleaning?
That's the whole test, really, not a calendar. Pull the wheel off the truck, spin it by hand, and listen for yourself: smooth and quiet for several seconds means you're fine; gritty, slow, or catching partway through means it's time. Riding through sand, rain, or just months of street grime is what gets a bearing to that point, not age by itself.
What You'll Need
- A solvent. This is the one spot where sources genuinely disagree, so pick based on what you've got: isopropyl alcohol at 90% or higher is the common recommendation, strong enough to cut through old grease without being as harsh as the alternative. Stick to 90%+ rather than the drugstore 70% kind; the extra water in lower concentrations is the real rust risk, not the alcohol itself. Acetone cleans just as well and dries faster, but it's harsher to handle and will melt a plastic container, so use glass or metal. Citrus-based cleaner is the gentlest option but can leave a slight oily film behind.
- A small container (glass or metal if you're using acetone).
- A thin, sharp tool, like a pin or a small screwdriver, to pop the shields off.
- Fresh lubricant for after cleaning (see the FAQ for the oil vs. grease choice).
- Never use water or soap on the bearing itself, since it promotes rust. If the shields need a wipe, clean those separately in soapy water, away from the bearing.
Step by Step
- Pull the wheels and bearings. Pop the wheels off with a skate tool, then press the bearings out of each wheel. Eight bearings total if you're doing the full board: two per wheel.
- Pop the shields. Each bearing has a shield (sometimes two) covering the balls. Work a pin or small screwdriver gently around the edge until it pops free. Don't force it: a bent shield won't seat back on right.
- Soak and swish. Drop the bearings in your solvent and let them sit for a few minutes, up to 30 if they're really grimy. Swish the container every so often, or use a soft-bristle brush to knock loose debris free.
- Dry completely. Any solvent left inside will thin out your new lubricant and undo the cleaning. Let the bearings air dry fully, or spin them by hand on a skate tool's axle to help fling out whatever solvent is left inside.
- Relube. A few drops of fresh lubricant per bearing, worked in by spinning the bearing a few times.
- Reassemble and test. Shields back on, bearings pressed back into the wheels, wheels back on the trucks. Spin each wheel before you ride: it should sound the same as it did fresh out of the package.
Does WD-40 Work?
Not as a long-term fix. WD-40 will cut through old grease in a pinch, which is why people reach for it, but it's not a cleaner and it's not a lubricant. It doesn't pull the grit out of the bearing, and it won't hold up the way an actual bearing lubricant does. Use it only as a one-time degreaser before a real clean and relube, never as what you put back in.
How Often Should You Clean Them?
There's no fixed schedule. It depends on how much you ride and where. Skaters riding daily on rough streets or through dust and debris might clean every few weeks; someone cruising smooth pavement a couple times a month can go much longer. The spin test at the top of this guide is a better signal than any calendar interval. That's the real lesson from both the ABEC and the bearing-picks guides: the stuff you do here matters more than the brand name or the rating on the box.
For picks on which bearing to buy in the first place, see our best skateboard bearings roundup. For why ABEC rating isn't the number to chase, see the skateboard bearings guide.
FAQ
Can I clean bearings without removing them from the wheel?
Not properly. You can flush some grit out with a quick spray while they're still pressed in, but you won't get the shields off or fully swap the lubricant that way. For a real clean, pull them out.
What lubricant should I use after cleaning?
Thin bearing oil or grease: that's the real choice, not "speed cream vs. oil," since speed cream is itself a thin oil, just one brand's version of it. Thin oil is what most skaters use day to day: low-viscosity, synthetic, built for speed, but it needs reapplying more often. Grease is thicker and lower-maintenance, which suits cruising, but it makes the bearing feel less free-spinning, not what you want if you're chasing roll speed. Skip household oils; they're not formulated for this and can gum up or evaporate.
The rest of your setup matters just as much. See the complete setup guide for how bearings fit with your deck, trucks and wheels. A best skateboard grip tape guide closes out this cluster.