Some links on this page are affiliate links. If you buy through them, SkateSetups may earn a commission at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.
Your trucks should be loose enough to turn the board just by leaning, but tight enough that you're not fighting wheel wobble at speed or kick-turning around every obstacle. If you have to kick-turn constantly on flat ground, your trucks are too tight. If the board feels twitchy or hard to control going straight, they're too loose.
The Stability vs. Turning Trade-Off
Every adjustment you make to a truck's kingpin nut is a trade between two things: how easily the truck turns, and how stable it feels at speed.
Looser trucks let the hanger rock side to side more freely. That gives you sharper, easier turns and more carve, but past a certain point the board starts to feel unpredictable, especially rolling fast, where a loose truck can wobble instead of holding a line.
Tighter trucks resist that side-to-side rock. They feel more stable at speed and more locked-in for grinds and landings, but turning takes more effort. Go too far and the board stops turning by lean at all. You're stuck kick-turning everywhere.
Neither end is "correct." It's a dial, and where you land on it depends on what you're skating and how you skate it.
How to Check and Adjust It
The kingpin nut, the big nut in the center of the truck, is what you're adjusting. Tightening it compresses the bushings around the kingpin; loosening it lets them move more freely.
A simple way to set a baseline: tighten the kingpin nut until the bushings feel snug, not crushed. You should be able to turn it with a skate tool without putting your full weight behind it. If it takes serious force to budge, you've gone too far.
While you're in there, check your mounting hardware too. The bolts holding the trucks to the deck should be snug with zero play. That's a separate adjustment from kingpin tightness, but a loose mounting bolt can feel like a truck problem when it isn't one.
From that baseline, adjust by feel. Ride it, then go a quarter-turn looser or tighter depending on which direction feels wrong. It takes a session or two to land somewhere you're happy with, and that's normal.
By Discipline
These are tendencies, not rules. Plenty of pros land outside them.
Street skaters generally run a middle-to-tighter setting. The added stability holds up better on grinds, ollies, and landing impacts, where a truck that turns too easily can feel unpredictable underfoot.
Cruising setups usually run looser. You're after smooth, easy carving rather than sharp control, and a loose truck gets you there with less effort.
Vert and bowl skaters tend toward tighter trucks for stability at the speeds those transitions build up. One real exception worth knowing: if you're skating bowl and find yourself kick-turning when you should be carving through a line, your trucks are probably too tight for that terrain. Bowl riding depends on being able to carve, not just hold a straight line.
For a deeper look at how truck choice overall splits by discipline, see Independent vs Thunder Trucks and the most-used trucks ranking.
Bushings Are Part of This
Kingpin tightness doesn't work alone. It works against the bushings sitting on either side of the kingpin. Harder bushings resist turning more at the same kingpin tightness; softer bushings turn easier at that same setting. Changing bushing hardness is often a better fix than just cranking the kingpin nut tighter or looser.
Harder bushings lead among the pros we have bushing data for. Bones Hard Bushings covers 11 of the roughly 22 setups where we have bushing hardness on record. That's a small sample (we don't have bushing data for most of the pros in our database), but what we do have skews firmly toward the harder end, consistent with the stability tendencies above.
Browse the most-used bushings ranking for the full breakdown, or see the full bushings guide for how to pick hardness and shape.
For Beginners
If you're just starting out, lean toward tighter rather than looser. A tighter setup resists unwanted side-to-side rock, which makes the board feel more predictable while you're still finding your balance. As your riding improves and you start wanting sharper turns, loosen the kingpin nut gradually, a quarter-turn at a time, rather than jumping straight to loose.
FAQ
What happens if my trucks are too tight?
The board resists turning by lean, so you end up kick-turning around things you should be able to carve through. In extreme cases, an over-tightened kingpin nut can also crush the bushings, which changes how they respond over time.
What happens if my trucks are too loose?
The board turns too easily and can feel unstable or wobbly at speed, especially rolling fast in a straight line. Mounting bolts with play can make this worse, so rule those out first.
Do I need new bushings, or should I just adjust tightness?
Try adjusting kingpin tightness first. It's free and takes two minutes. If you're maxed out on tightness in either direction and the board still doesn't feel right, that's when swapping bushing hardness is worth doing.
Trucks are one piece of the picture. See the complete setup guide for the rest.