Guide · Trucks & Bushings

Skateboard Hardware Size Guide: Bolts & Risers

7/8" to 1" with no risers, and why online charts disagree the moment you add one.

Some links on this page are affiliate links. If you buy through them, SkateSetups may earn a commission at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

Hardware is the least complicated spec in a setup: 7/8" to 1" bolts with no risers, and roughly an extra ⅛" of bolt length for every ⅛" of riser you add. Get the length close and you're done. There's no feel or performance difference to chase here the way there is with wheels or bushings.

What Pros Actually Ride

Among the pros we track with hardware data, Diamond Supply Co. leads:

Brand Pros riding it
Diamond Supply Co. Hardware 15
Independent Hardware 10
Hardies Hardware 7
Shake Junt Hardware 6
Diamond Hardware 5
Leftover Hardware 2
Mini Logo 1
Modus Hardware 1
Diamond Supply Co. Sean Malto 1
Biggest Little Hardware 1

A long tail of smaller brands make up the rest. See the most-used hardware ranking for the full list.

Hardware length almost never gets mentioned by name, so we don't have a real length breakdown to show you, except for 2 products in our database that spell the length out directly in the product name. That's a thin sample, 2 out of the 59 hardware entries we track, but it's a real confirmation that 7/8" shows up in actual pro setups, not just on a retailer's chart.

Bolt Length by Riser Thickness

The base case is consistent everywhere: 7/8" to 1" bolts with no risers. Add a riser and you add length. Most sources agree a ⅛" riser needs right around 1" bolts.

Past that, charts start to disagree. For a ¼" riser, one retailer's chart calls for 1⅛" bolts, another calls for 1¼". That's a real eighth of an inch of difference, not a rounding error. The safest move: measure your actual riser thickness and go slightly long rather than short. A bolt with a little extra thread showing is a non-issue; a bolt that's too short to fully engage the nut is a real one.

Do You Even Need a Riser?

Skip the charts for this one and just check your own setup. Flip the board over and push a wheel up toward the deck, the same motion it makes on a hard turn. If it touches, you need a riser (or a thicker one than you've got).

Online sources don't agree on a wheel-size cutoff for this. One retailer says 54mm wheels are fine without a riser, another says 55mm, another says 56mm. One gives a more detailed breakdown: no riser needed up to 54mm, ⅛" riser for 55–58mm, ¼" for 58–62mm, ½" for 62–68mm. Treat all of these as rough starting points, not rules, since your deck's wheel wells and truck height matter too.

Your truck tightness and bushings setup affects it as well, which is why the flip test beats any chart.

Shock Pads vs. Risers

These get sold next to each other and sometimes confused. A riser's job is clearance: it physically lifts the trucks away from the deck so bigger wheels have room to turn without hitting.

A shock pad does something different. It's about vibration dampening, usually a softer material that absorbs some of the harshness of rough ground, with little to no added height.

Some riders run a thin ⅛" riser purely for the dampening effect, not because they need the clearance. If that's your goal, a dedicated shock pad does the same job without changing your ride height as much.

FAQ

How do I check if my bolts are too short or too long?

Too short and they won't fully engage the lock nut, which means they can back out over time. Too long and they'll stick out noticeably past the nut. A bolt that sits roughly flush, maybe a thread or two of extra length showing, is right.

Can I stack risers?

Yes, risers stack, and it's a common way to fine-tune clearance without buying a single thicker one. Just re-check your bolt length every time you add a layer: stacking two 1/8" risers needs the same bolt length as one 1/4" riser.

Hardware and risers might be the least exciting part of a setup, but getting them right keeps everything else, trucks, bushings, wheels, doing its actual job. See the complete setup guide for the rest.

Round Out the Rest of Your Trucks

Browse the most-used hardware among pros, or dial in tightness and bushings.