Guide · Trucks & Bushings

Skateboard Truck Size Guide

Match axle width to deck width, not the number on the box. Here's why Ace, Tensor, and Krux charts online keep contradicting each other.

Some links on this page are affiliate links. If you buy through them, SkateSetups may earn a commission at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

Truck size comes down to one thing: axle width should match deck width, within about an eighth to a quarter inch. The size number printed on the truck or the box isn't the axle width in inches, and it doesn't mean the same thing from one brand to the next. Once you know each brand's actual chart, though, matching is simple.

What Brands Pros Actually Ride

Among the pros we track with verified truck data, Independent leads by a wide margin:

Brand Pros riding it
Independent Trucks 177
Thunder Trucks 96
Venture Trucks 41
Ace Trucks 26
Royal Trucks 10
Krux Trucks 8
Slappy Trucks 6

A handful of smaller brands make up the rest. Independent and Thunder alone cover the large majority of the pros we track. See the most-used trucks ranking for the full list, or the Independent vs Thunder Trucks comparison for size-specific pro data on those two brands, which we won't repeat here.

Cross-Brand Size Chart

Check just one online chart for Ace, Tensor, or Krux sizing and you'll probably come away confused. Several retailer charts for these brands flat-out contradict each other. It turns out the reason isn't that anyone's wrong, it's that Ace sells two different lineups, AF1 and Classic, with slightly different axle widths at the same nominal size. A chart that doesn't specify which lineup it means will look like it disagrees with one that does.

Deck width Ace AF1 Ace Classic Tensor Krux
~7.6–7.75" 22 (7.75") 22 (7.60") N/A 7.6 (7.60")
8.0" 33 (8.00") 33 (8.00") 5.25 (8.00") 8.0 (8.00")
8.25" 44 (8.25") 44 (8.35") 5.5 (8.25") 8.25 (8.25")
8.5" 55 (8.50") N/A 5.75 (8.50") 8.5 (8.50")

Independent, Thunder, and Venture follow the same match-the-axle-to-your-deck logic. For an 8.0" deck specifically, that's Independent 139, Thunder 147, and Venture 5.25, a pairing that held up consistently across every source we checked. For the fuller Independent/Thunder size breakdown, including less common sizes and real pro usage by size, see the full Independent/Thunder size breakdown.

One caution that still applies: brands update their lineups between model years. If a number here or on any chart doesn't match what's printed on the truck or the brand's current site, go with the brand's own current chart.

How to Measure and Check Fit

Axle width and hanger width aren't the same measurement. Axle width is the full length of the axle, tip to tip, and that's the number that needs to roughly match your deck width. Hanger width is just the hanger itself, which is narrower.

The matching rule: get your axle width within about an eighth to a quarter inch of your deck width. Narrower trucks than your deck will feel unstable and make wheelbite more likely on tight turns. Wider trucks will stick out past the edge of the deck, which looks and feels off and changes how the board responds underfoot.

If you're buying trucks separately from a deck you already own, measure the deck's actual width rather than trusting the stated size. Decks can run slightly off their printed measurement.

Fit is only half the equation. Mounting bolts and riser pads have their own sizing logic, covered in our hardware and riser pad guide.

FAQ

What happens if my trucks are too narrow or too wide for my deck?

Too narrow and the board feels tippy and unstable, with a higher chance of wheelbite on hard turns. Too wide and the trucks stick out past the deck's edge, which throws off your foot placement and the way the board responds to pressure.

Does truck height matter for sizing?

Height is a separate spec from axle width. It's about ground clearance and wheelbite risk with bigger wheels, not about matching your deck.

See our truck tightness guide and bushings guide for how height interacts with the rest of your setup.

What if my deck width falls between two listed sizes?

Round to the nearest size within the ⅛–¼" tolerance. If you're exactly in between, sizing up slightly is generally the safer call than sizing down.

See the complete setup guide for how truck sizing fits into the rest of your setup.

Get the Rest of Your Trucks Dialed In

Browse the most-used trucks among pros, or set your tightness and bushings.