Building a skateboard setup from parts takes about 20 minutes with a skate tool: grip the deck, mount the trucks, press bearings into the wheels, mount the wheels, and adjust truck tightness to taste. Here's each step in enough detail to actually do it, not just the one-line version.
What You'll Need
Components: a deck, two trucks, four wheels, eight bearings (two per wheel), mounting hardware, and a sheet of grip tape. For what each of these actually costs, see our skateboard setup checklist.
Tools: a skate tool is the one thing worth having. It combines the socket sizes for axle nuts, kingpin nuts, and truck bolts into a single handle, which is faster and easier on your knuckles than a set of separate wrenches. You'll also want a utility knife or razor blade for trimming grip tape.
Step 1: Apply the Grip Tape
Peel the backing off the grip tape and lay it onto the deck, pressing from the center outward to avoid trapping air. Some bubbling is normal, especially near the deck's concave; pop any bubbles with a pin and smooth them flat before moving on.
Once it's down, find the truck bolt holes from underneath and punch through the grip tape at each one with something pointed (a screw or the tip of your skate tool works). Then trim the excess tape around the edges of the deck with your utility knife, running the blade along the edge at an angle so it follows the deck's curve.
Step 2: Mount the Trucks
Push the mounting bolts through from the top, first through the punched holes in the grip tape, then the holes in the deck. If you're using riser pads to avoid wheel bite with bigger wheels, they go between the deck and the trucks here. They're optional, and most setups don't need them.
Thread the nuts on from underneath and tighten them by hand first, then with your skate tool. Start with the two center bolts on each truck and work outward instead of cranking one corner down fully before moving to the next. Doing it out of order can seat the truck unevenly against the deck.
Step 3: Install Bearings and Wheels
Press two bearings into each wheel, one on each side. If a bearing is fighting you going in, a drop of lube on the bearing itself makes it slide in cleanly. Don't force it with pressure alone, since that can damage the bearing shield. For the actual bearing choice and the ABEC-rating myth, see our skateboard bearings guide; for keeping them running well once they're in, see how to clean skateboard bearings.
Slide each wheel onto a truck axle and thread the axle nut on. Snug is the target: tight enough that the wheel doesn't wobble, loose enough that it still spins freely. Overtightening here is a common mistake: it can bind the bearings and make the wheel drag instead of roll.
Step 4: Adjust Truck Tightness
The kingpin nut on each truck controls how easily it turns: tighter resists turning and feels more stable at speed, looser turns easier but feels less locked-in. There's no universally correct setting. It's a matter of preference, and both trucks should be adjusted to match each other. See our truck tightness guide for how to actually dial this in rather than guessing.
Step 5: Test Before You Ride
Check that every nut is tight: axle nuts, kingpin nuts, and the mounting bolts holding the trucks to the deck. Spin each wheel by hand; it should turn smoothly without catching or grinding. Take a short, slow test roll somewhere flat before riding normally, so you catch anything loose or rubbing while you're still close to the ground.
Common Mistakes While Assembling
- Cranking down mounting bolts unevenly. Tightening one corner fully before the others can seat the truck at an angle. Go center-out, a little at a time.
- Overtightening axle nuts. This can bind the bearings enough that the wheel drags instead of spinning freely.
- Skipping the test roll. A loose nut or a rubbing wheel is much easier to catch standing still than at speed.
For the full list of setup mistakes, see our dedicated guide.
FAQ
Do I need a skate tool?
Not strictly. A set of the right-sized wrenches and a screwdriver will work. But a skate tool combines everything into one handle, which is faster and far less likely to skin your knuckles on the deck mid-adjustment.
What if I get a bubble under my grip tape?
Pop it with a pin and press the tape flat before it sets. Small bubbles near the concave are normal during application; just don't leave them trapped once the tape has bonded.
How do I know if my trucks are too tight or too loose?
Too tight feels stiff and hard to turn even at a stop. Too loose feels wobbly or vague at speed.
This covers assembly. For sizing, discipline-specific builds, and everything else that goes into a setup, see the complete setup guide.