Guide · Build & Assemble

9 Common Skateboard Setup Mistakes (And How to Fix Them)

Most of these are about how it's put together, not what you bought.

Most skateboard setup mistakes aren't about buying the wrong gear. They're about how it gets put together or matched up. Here are the nine setup and assembly mistakes that come up most, roughly in the order you'd run into them while building a board.

1. Tightening Truck Mounting Bolts Unevenly

Cranking one corner of the truck down fully before moving to the next pulls that corner tight against the deck while the others are still loose, which can seat the whole truck at a slight angle once everything's finally tight. A truck mounted crooked turns differently on each side, even if every bolt ends up torqued the same. Fix: go center-out, a little at a time on each bolt, so the truck settles flat the whole way through.

2. Overtightening Axle Nuts

Snug is the target, not tight. Crank an axle nut down past snug and it can bind the bearing enough that the wheel drags instead of spinning freely. You'll feel it as a wheel that slows down fast when you spin it by hand, or doesn't sound right compared to the others. Back the nut off slightly until the wheel spins freely but doesn't wobble side to side.

3. Skipping the Test Roll

A loose bolt or a wheel rubbing the deck is far easier to catch standing still in your driveway than at speed on a hill. Spin every wheel by hand, check that nothing's loose, and take a short, slow roll on flat ground before riding normally. If something's off, you'll feel it immediately at low speed instead of finding out the hard way.

4. Trucks That Don't Match the Deck Width

Truck sizing runs on axle width, not the size name printed on the hanger, and a mismatch goes wrong in two different directions. Trucks too narrow for the deck make the board feel unstable and twitchy. Trucks too wide create their own clearance problems and just look wrong hanging off the edges. See our truck size guide for how to actually match axle width to deck width instead of guessing from the size name.

5. Hardware That's the Wrong Length for Your Risers

Add risers and you need longer hardware; that part everyone agrees on. The exact length for a given riser thickness is where sources genuinely disagree, so rather than guess, see our hardware and riser guide for how to actually size bolts to your specific setup instead of assuming a number that might be wrong for your deck.

6. Bigger Wheels Without Adding Risers

Wheelbite (the wheel actually touching the deck on a hard turn) gets more likely the bigger your wheels get, especially on lower trucks, unless you add clearance to compensate. If you're sizing up from street wheels to something larger for cruising or rough ground, check whether your current trucks and deck have enough clearance first. Our hardware and riser guide covers when a riser actually solves this and when it doesn't.

7. Stock Bushings That Don't Match You

Trucks ship with whatever bushings the brand decided to include, which isn't necessarily right for your weight or how you ride. A setup that feels too stiff to turn or too loose to trust at speed is often a bushing problem, not a truck problem. See our bushings guide for how hardness and shape actually change the feel.

8. Never Re-Checking Hardware After the First Few Sessions

New hardware settles in after actual riding. Bolts that were torqued correctly on day one can work slightly loose after a handful of sessions, especially around the truck mounting bolts. A quick check every few sessions, not just once at setup, catches this before it becomes a real problem.

9. Buying the Cheapest Option Everywhere, Not Just Where It Doesn't Matter

Some parts barely vary with price: grip tape and hardware are grip tape and hardware. Deck, trucks, and wheels are different: fit and sizing actually change how the board feels, so chasing the lowest price on those specifically can leave you with something that doesn't suit your height, weight, or style. Our setup checklist breaks down exactly where a few extra dollars matters and where it doesn't.

FAQ

How do I know if my trucks don't match my deck?

The board will feel unstable (trucks too narrow) or the wheels will stick out awkwardly past the edges (trucks too wide). Check axle width against deck width directly rather than matching size names, since those don't map the same way across brands.

Do I need risers for bigger wheels?

Not always, but it depends on your current truck height and deck's wheel wells. If you're getting wheelbite on hard turns after sizing up, a riser is the fix. If you're not getting wheelbite, you don't need one yet.

How often should I check my hardware?

At minimum, once after your first few sessions, since new hardware settles in and can work loose. After that, a quick check whenever something starts to feel different is enough. It doesn't need to be a fixed schedule.

Once your setup's dialed in, see the complete setup guide for how every part fits together, go back to the assembly guide if you're still putting it together for the first time, or see our picks for the best skateboard setup for beginners if you're starting from scratch.

Fix It Right

Get the sizing and tuning guides for the parts that matter most.